ZS direct acting solenoid valve

Electromagnetic valve is an industrial equipment controlled by electromagnetism, which is an automation basic component used to control fluids. It belongs to the actuator and is not limited to hydraulic or pneumatic systems. It is used in industrial control system to adjust the direction, flow, speed and other parameters of medium. The solenoid valve can be combined with different circuits to achieve the expected control, and the accuracy and flexibility of the control can be guaranteed. There are many types of solenoid valves, and different solenoid valves play a role in different positions of the control system. The most commonly used ones are one-way valves, safety valves, directional control valves, speed regulating valves, etc.

The solenoid valve has a sealed chamber with through holes at different positions, each connected to a different oil pipe. The middle of the chamber is a piston, and there are two electromagnets on both sides. The magnetic coil on which side is energized will attract the valve body to which side. By controlling the movement of the valve body, different oil discharge holes can be opened or closed. The oil inlet hole is usually open, and hydraulic oil will enter different oil discharge pipes, and then push the piston of the oil cylinder through the pressure of the oil, The piston drives the piston rod, which drives the mechanical device. In this way, mechanical motion is controlled by controlling the current flow of the electromagnet.

An electromagnetic valve is a fluid control element that is controlled by the moving piston of an electromagnetic coil to attract electromagnetic force. It is an actuator for automated equipment pipelines. Below are illustrated working principles of a direct piston type electromagnetic valve and a pilot piston type electromagnetic valve, with manual reset electromagnetic network working principles and self holding electromagnetic valve and gas emergency cut-off electromagnetic valve working principles.

Features: 1. Direct pull diaphragm type. 2. Zero pressure start, suitable for low-pressure systems. Media: air, gas, water, etc Fluid temperature: nitrile rubber: -5 ℃~80 ℃ EPDM adhesive: -5 ℃~100 ℃ Fluorine rubber: -5 ℃~120 ℃ Pressure: 0.~1.0MPa Connection dimensions: 3/8 ", 1/2", 3/4 ", 1", 11/4 ", 11/2", 2 ", Thread: G thread, NPT thread Diameter (mm): 10,15,20,25,32,40,50 Voltage: (DC) 12V, 24V (AC) 24V, 120V, 240V/60Hz; 110V, 220V/50Hz

ZCM solenoid valve is an actuator suitable for automatic temperature control in heating combustion medium pipelines using various gases such as urban gas, liquefied petroleum gas, and natural gas. It is widely used in gas heat setting in the textile and printing industries, furnace heating in the glass and light bulb industries, and gas heating self-control systems in other industries.

The XUVAL88-151 series pump is a radial suction high-temperature medium transfer circulation vortex pump, which transports liquid without particles or fibers. The main characteristics of the pump are small volume, exquisite appearance, high head, fast flow rate, and stable performance.

Product introduction: Spring type double safety valve is suitable for steam, water and other media equipment and pipelines with working temperature ≤ 350 ℃. As overpressure protection device. Connecting flange standard according to JB/T... 94 series 1A38Y,A43H,A37H double safety valve is installed on the Y-joint with two A48Y or A47H safety valves of the same specification, and its nominal diameter series refers to the inlet diameter of the Y-joint.

Q47F fixed ball valve is suitable for industries such as chemical, petroleum, natural gas, metallurgy, and natural gas long-distance pipelines containing hydrogen sulfide media, impurities, and severe corrosion.

Product overview of Z940H/Y electric high temperature and high pressure gate valve: The Z940H/Y electric high temperature and high pressure gate valve is suitable for the pipelines of various systems in petroleum, chemical, hydraulic, and thermal power plants with a nominal pressure of PN1.6～16.0MPa and working temperature ≤-29℃～550℃ to cut off or connect the pipeline medium. . Applicable media are: water, oil, steam, acid, alkali, ammonia, urea, sulfur-containing natural gas, etc. The operation modes are: manual, gear drive, electric, pneumatic, etc.